Tip 1: How to install Windows on a new hard disk

When buying a new computer the question immediately arises installation of the operating system on it.To do this, do not need to have additional skills and knowledge.The procedure for the installation of Windows is quite simple.
you need
  • - computer;
  • - installation disk Windows.
Guide
1 Turn on the computer to install Windows on a new hard drive.Insert the installation disc with the operating system.If after a couple of minutes is not a window installer, and you see a message similar to the Insert system disk and press any enter, then you must restart the computer and enter the BIOS.
2
To do this, boot your computer, press Del, or press F2, depending on the BIOS version, then go to the item Advanced, and select Advanced BIOS Features.You need to find the option First Boot Device and select the value of her CD, so to be able to install the operating system on the hard drive.
3
Press F10, to save the changes and restart the computer to install Windows on a new hard disk.The d
ownload will start from the installation disk.After downloading the installer files will appear in which you will select the drive for installation.
4
Highlight the desired disc, press "C" to create a partition on the disk to install the operating system.Enter the desired time action disk in megabytes, as practice shows, for the future of disk with enough thirty gigabytes.It will be available the operating system and all installed software.
5
Create, if necessary, other logical disks, for that do the same with the unallocated space on the disk.Next, select the partition to install the operating system Windows, to do this, select the section, and then press Enter.
6
In the next window to format your partition.When installing the operating system on a new hard drive is necessary to select the format "Format Partition system NTFC».Not recommended a quick format.Wait for the disc format and copy files to the disc.The computer will restart.
7
Follow the wizard installation, select the required parameters for it: the region accounts, network connection settings, and so on.Wait until the installation is complete.Restart the computer.Installing the operating system is complete.

Tip 2: How to put a new hard drive

Modern hard drives very reliable and can work out a very long time.But no one is safe from damage any equipment.If a hard drive fails, the likelihood that it can be mended, not high.Then you have to purchase and install a new hard drive.The process is not difficult, but there are some nuances associated with the type of hard drive interfaces and motherboards.It is necessary to choose the hard drive, which is suitable for the interface of your motherboard.
How to put a new hard drive
you need
  • computer hard drive with a SATA-connector or a connector IDE, a screwdriver.
Guide
1
To start find out what interface your motherboard is equipped with.This is done by looking at the technical documentation to your computer.Look, if there is on the motherboard SATA-interface.If you do not have technical documentation, it is possible to see the connection interfaces to the motherboard itself.After all, in any case, have to open the system unit.
2
power from the computer.Remove the screws that secure the system cover and remove the cover of the system unit.Now look for the inscription motherboard SATA.Nearby are the interfaces to connect SATA.Generally, these interfaces are in the lower right corner of the board.Note that the SATA-interface may be missing for quite old motherboards.
3
If SATA-interface has been detected, then the hard drive you should buy as a SATA-connector.If you did not have this interface, you can purchase a hard drive with built-in connectivity IDE.
4
If you change a non-working hard drive, remove it from the system unit.To connect a SATA-HDD, connect one end of the SATA-cable to the hard drive, the hard drive itself, set the desired compartment of the system unit.The other end of SATA-cable to a free SATA-connector on the system board.Then connect the power supply to the HDD.
5
connect IDE-HDD you need using the 80-wire cable.Several of these trails should be packaged with your computer or motherboard.They can also be purchased separately.Find the IDE-connector on the motherboard.There may be two - primary and secondary.Although one IDE-connector can be connected and the drive, and hard drive, this is not recommended, otherwise you'll have to use special jumpers.Now, as in the previous case, connect the hard drive to the motherboard using the 80-core flat cable.Then connect the power supply.
6
Next, check the hard disk.The cover of the system unit do not rush to close.Connect the computer power and turn it on.If the hard drive is working properly, close the cover of the system unit.
Sources:
  • how to install new windows

Search

Related Posts

Categories