Tip 1: How to make a DVD in your laptop

Despite the rapid development of computer technology and the emergence of devices such as a portable HDD or USB flash drive, DVD-ROM is still one of the most popular media.Low price and low cost of the equipment did record DVD business simple and cheap enough.To install the DVD on a laptop , you must use special software.
you need
  • - Laptop with writing DVD-drive;
  • - special software.
Guide
1
Walk into any convenient computer store and buy a few DVD-ROM drive.Media Formats unimportant, as modern notebook computers capable of working with both the DVD + R (W), and from the DVD-R (W).However, we must bear in mind that some domestic players obsolete may refuse to play some discs.
2
Buy format discs DVD-R, if you need a one-time recording or the file size is small.Purchase a DVD-RW disc for repeated use.The last option for those who want to be able to edit the previously recorded material.
3
Determine the range of tasks that must be done.Based on goals download or purchase in a
store special software for recording DVD.To make a DVD-ROM, laptop , you will need different software.
4
To make a data disc or to copy media files, install the free recording center Ashampoo Burning Studio from the page http://biblprog.org.ua/ru/ashampoo_burning_studio_free/.A good alternative to this program is Free studio 56: http://vipcenter.ws/programmy/3681-free-studio-533.html.
5
Insert Tray DVD-drive disk and run the program to record.Select the files - be it photos, documents, movies, etc. Content.Transfer them to the DVD-drive icon.Set the writing speed or entrust adjustment data program.
6
Start the data transfer between the computer and the hard drive DVD-drive.Wait until recording is finished.Try not to move the laptop during the entire process, in order to avoid unnecessary mistakes.
7
Check the quality of the recording.If failed, check the DVD on physical damage or dirt on the reflecting surface.
8
To make a bootable DVD, for example, to run programs on the operating system installation, use the application menu titled "Creating a bootable disk."Follow the instructions of a special wizard, leading step by step to a successful conclusion of the process.Note that boot disks better record at a slow speed.Also, do not insert into the computer DVD-RW, since such drives are less reliable and often fail during recording the boot information.
9
To create a beautiful film to DVD using the built-in Windows utility called "Studio Windows Live».This program will edit the footage quality, provide an opportunity to choose a colorful menu for the movie.And after you finish editing writes data to a DVD-ROM

Tip 2: How to replace the DVD-ROM drive in the laptop

No matter how you try to extend the life of your notebook, still some of its items will be out of commission.The "risk" is DVD- drive , Laser LED that simply fade with time.It is also the cause of failure can be any external influence (moisture gets inside, sand, inaccurate close tray, etc.).In connection with this have to completely change DVD- drive .
How to replace the DVD-ROM drive in the laptop
Guide
1
In most cases, changing the DVD- drive yourself, you run a high risk.The fact that the improper installation of this device may have a conflict with the motherboard of the computer associated with the interrupt bus IDE (ATA).As a result - drive CD-ROM drive is not just determined by either the operating system or BIOS.To prevent this, just follow some rules.
2
To start, determine the type of DVD- and drive.To date, there are interfaces like IDE (ATA) and SATA.Unfortunately, often there is a problem in the first case.
3
Then use a screwdriver to get rid of the mounting screws located on the lid of the CD-ROM drive.Take a thin tool (you can use a paper clip or a usual pin) and use it to open the tray device.Finally get rid of the top cover and pull the tray forward.
4
Now look what mode is DVD- drive .In most cases, these devices are released with the expectation that the system automatically determines the necessary parameters to it.Unfortunately, on the IDE bus will almost always be assigned mode «Master», that drive IT to interrupt conflicts with the operating system.So carefully make a jumper drive and switch Cable Select, or Slave, depending on the model chosen.
5
this purpose Jumper pins 47 and 49 placed into the IDE connector device.It would have to be done manually, asspecial pins for this purpose is not intended.Take a small wire and solder it to the contacts.You will need only a few drops of solder.
6
Then gather your DVD- drive , moving in the opposite direction.Ieclose the tray, cover it with a lid, tighten screws.
Sources:
  • what drive in a laptop

Search

Related Posts

Categories