Tip 1: How to restore the default BIOS settings

in endless attempts to improve performance and operating parameters of the computer, many users will sooner or later get to the BIOS settings of the motherboard and start something in them changed.They overclock the CPU, change the parameters of the memory, hard drive and so on.And even an experienced user, such manipulation may lead to the fact that the computer stops functioning properly or is not included.In this case, you need to reset your BIOS.
you need
  • - Computer;
  • - screwdriver.
Guide
1
If the computer is turned on and "reach" to display system status, go to Control Panel BIOS and scroll, which is called the Restore default settings or some similar phrase.Select this option and press Enter.Then on the Exit tab select "Save and Exit" and confirm the changes made in the BIOS, and pressing Enter.
2
If the computer does not boot to the above point, reset the BIOS using a special physical switch or button-jumper on the motherboard.The instructions to get the board description p
age located on her jumper and check which of them performs resetting the settings BIOS.
3
Turn off your computer and remove the side cover, to allow access to the board.Locate the jumper and switch it to the position reset.On most motherboards is a set of three pins, two of which are closed to each other jumper.This jumper relocate to a nearby location and wait a few seconds.Then return it to its original position and turn on the computer.
4
On some models the board, especially in those which involve acceleration, there is a reset button BIOS.If you have this motherboard, just click once on the button, you can then turn on the computer.
5
Another way to reset the BIOS settings is to extract the battery from the motherboard.Carefully remove it from the socket, wait a few minutes and set back.This method is good that the battery is clearly visible on the board and its location is not necessary to look for with the help of the instructions, but it does not works on all models of motherboards.
6
If the above steps did not lead to success, most likely, the data on the flash BIOS module damaged.In order to "revive" the board in this state, contact the service center.To restore operation requires a special device - programmer, which is hardly a home.

Tip 2: How to make the restoration of settings Bios

Many computer settings can be configured using only the Bios.But at the same time among the Bios-language menu is not Russian.And inexperience or accidentally, you can make a mess in the settings that the computer even booting.Of course, then you have to look for the cause, re-enter the settings and change various settings, often to restart the computer.Meanwhile, there is a way simpler - recovery settings Bios.
How to make the restoration of settings Bios
you need
  • - computer;
  • - screwdriver.
Guide
1
If you reset the default settings, it will use the basic setup Bios, which have been established as the standard.You can do this in several ways.The first of them - is reset settings directly from the Bios-menu.To do this, go to the Bios, and then go to the tab Exit.
2
then select Load Setup Defaults.The computer will reboot, and all settings will be restored.But there are cases where this method does not help.In this case, you will be other ways.
3
unplug the computer.Next, remove the mounting screws, and then remove the system cover.Locate the battery on the motherboard.It is this battery and is responsible for maintaining the settings .Now act necessary depending on the situation.Check whether the batteries near a small bridge.If you managed to find the jumper, just move it to another position.After that, the settings will be reset.
4
Also, instead of a switch, you may find the button.Near it should be an inscription CMOS.This reset button settings .Click on it.After that, the settings will be restored.
5
If your motherboard was not a reset button configuration , or switch, then we must act so.Bottom near the batteries is a small lock, it is clearly visible.Take an ordinary screwdriver and click on the clip.After that, remove the battery from the slot.
6
After the battery is removed, you will need to wait for some time.For each model, the motherboard requires different time settings reset .In some - it is one, two minutes, in the other - an hour.Then insert the battery again.After this adjustment Bios will be restored to the standard.

Search

Related Posts

Categories